Partition format is not supported hikvision

Partition format is not supported hikvision


  • Format DVR Hard Drive
  • Hikvision HDD error: HDD is not detected (solved)
  • Playback not working
  • The good news is this can easily be accomplished with almost any medium-range and up IP camera, and even some cloud video surveillance platforms allow local storage options to be easily configured and retrieved from the cloud apps. Our screenshots are from a QNAP device but these steps are generally true for any device. Hikvision cameras require a dedicated partition for their IP camera. This is probably the most important and surprising!

    Each camera writing data to the partition requires its own share folder. This is a good idea to keep your data organize anyway. Are you enjoying our tutorial on this topic? We hope so! If you want to learn how to setup cloud video surveillance with Hikvision click here.

    Begin by, i ensuring your NAS basic setup is complete according to its user manual general setup, firmware updates, etc , ii you have your login credentials handy, iii the NAS is connected to your local network including identifying its internal IP address , and iv you can reach the NAS UI from your web browser. Step 2: Basic Hikvision Setup. Follow your NAS instructions for creating a partition — if using a new or separate hard disk drive HDD , create a partition on that particular drive.

    Step 4: Create Share Folders. You will need to create a share folder for each camera that will be using the NAS. Screenshot below shows where this is done. Here you click on any slot and fill in the server address internal IP of the NAS and the file path share folder you created in step 4. Also enter the username and password of the NAS.

    Use the Test button to validate connectivity to your NAS. Step 6: Configure your Hikvision camera recording settings. This is probably worth a blog post in and of itself, but the basic idea is you need to configure the Hikvision IP camera so it knows when you want the camera to record motion detection, scheduling, etc and where you want it to record in this case, the NAS. Figure 3: Hikvision Storage and Event Config There is a lot more to this topic than can be covered in a short blog post, but these are the main steps and you are now also aware of the main stumbling blocks to getting NAS recording setup for your Hikvision camera!

    And you know the best part? Our apps make it easy by ensuring the right configuration settings are applied to the camera, making it easy to setup and get going.

    Fixing the Hikvision HDD error 1. Hard Drive is faulty If the hard drive is bad or faulty, the Hikvision recorder will not be able to detect it. Is the hard drive new? Check it out on a desktop computer. Is the hard drive old and was used by a different kind of device? That may be a problem, especially if the hard drive is years old. Another thing you need to keep in mind, desktop hard drives have a short life span compared to the hard drives intended for security systems.

    Read the specs of your Hikvision unit and confirm that the installed hard drive is supported by the recorder. The power adapter that powers up the whole recorder is not able to power on the hard drive as well. The desktop hard drive may withdraw too much juice from the power adapter. Check the cables It happens quite often that the cables are loose and the hard drive cannot be detected by the system.

    To make sure everything is okay, turn off the Hikvision recorder, open up the top cover of your unit and locate the hard drive s. There should be two cables coming out of the hard drive: one is the data cable SATA cable , the other one is the power cable which gets power from the motherboard.

    In a few rare cases the power cable may be bad or even the SATA data cable. Ensure your cable is not damaged. Transfer the Hard Drive to another slot Usually the Hikvision recorders are able to support at least two hard drives. Turn off the recorder and disconnect the hard drive from its slot and plug it into the other slot just to test it out. Reconnect both the power cable and the data cable to new sockets on the motherboard. Related Posts.

    Step 4: Create Share Folders. You will need to create a share folder for each camera that will be using the NAS. Screenshot below shows where this is done.

    Format DVR Hard Drive

    Here you click on any slot and fill in the server address internal IP of the NAS and the file path share folder you created in step 4. Also enter the username and password of the NAS. Use the Test button to validate connectivity to your NAS. Step 6: Configure your Hikvision camera recording settings. This is probably worth a blog post in and of itself, but the basic idea is you need to configure the Hikvision IP camera so it knows when you want the camera to record motion detection, scheduling, etc and where you want it to record in this case, the NAS.

    Figure 3: Hikvision Storage and Event Config There is a lot more to this topic than can be covered in a short blog post, but these are the main steps and you are now also aware of the main stumbling blocks to getting NAS recording setup for your Hikvision camera!

    And you know the best part?

    Hikvision HDD error: HDD is not detected (solved)

    Our apps make it easy by ensuring the right configuration settings are applied to the camera, making it easy to setup and get going. Read the specs of your Hikvision unit and confirm that the installed hard drive is supported by the recorder. The power adapter that powers up the whole recorder is not able to power on the hard drive as well. The desktop hard drive may withdraw too much juice from the power adapter.

    Check the cables It happens quite often that the cables are loose and the hard drive cannot be detected by the system. To make sure everything is okay, turn off the Hikvision recorder, open up the top cover of your unit and locate the hard drive s. There should be two cables coming out of the hard drive: one is the data cable SATA cablethe other one is the power cable which gets power from the motherboard.

    Playback not working

    In a few rare cases the power cable may be bad or even the SATA data cable. Ensure your cable is not damaged. Transfer the Hard Drive to another slot Usually the Hikvision recorders are able to support at least two hard drives.


    thoughts on “Partition format is not supported hikvision

    1. I apologise, but, in my opinion, you are not right. I can prove it. Write to me in PM, we will discuss.

    2. On mine the theme is rather interesting. I suggest all to take part in discussion more actively.

    Leave a Reply

    Your email address will not be published. Required fields are marked *